BJC-210 Printer

General Info:

Adapter

AD-300 120vac

Alternative Drivers

Drivers you can use if the BJC-210 driver is not available.

• Windows : BJC-210/600/600e/800/4000
• DOS : BJ-200/200e/200ex (BJ Mode/Black)
• DOS : IBM ProPrinter X24 (BJ Mode/Black)

Cartridges

• BC-02 - Black Ink & Integral Print Head
• BC-05 - Color Ink & Integral Print Head

Cleaning Print Head

To clean the print head hold down the RESUME button with the printer switched on. Release the RESUME button when you hear two short beeps. The POWER LED will blink during print head cleaning. This should be repeated at least 5 times.

Printer Defaults

Switch printer off. Hold down the power button for the following number of beeps,

• 6 Beeps - LQ mode for USA
• 7 Beeps - BJ mode for USA
• 8 Beeps - LQ mode for Europe, Asia
• 9 Beeps - BJ mode for Europe, Asia
• 10 Beeps - BJ mode for UK and Asia

Self Test

Demo Test : Switch Printer off. Hold down power button for 1 beep. Press RESUME to stop.
Status Test : Switch Printer off. Hold down power button for 2 beep. Press RESUME to stop.
Ripple Test : Switch Printer off. Hold down power button for 3 beeps. Press RESUME to stop.
Nozzle Test : Switch Printer off. Hold down power button for 4 beeps. Press RESUME to stop.

Serial Number

Location - Label on back of machine near the power cord
Prefixes - EBS.....

Special Paper

• CF-102A4 - Transparencies. Used for producing overhead transparencies.
• GP-101A4 - Glossy Paper. Heavier coated paper, used for graphics.
• LC-101A4 - Coated A4 Paper. Coated paper used for high quality print.
• LC-301A4 – Bubble Jet Paper A4. Lightly coated, water resistant everyday usage paper.
• FS-101 - Fabric Sheet. Allows images to be printed onto 100% Cotton fabric (Machine Washable).
• BF-102A4 - Back Print Film A4. Used to produce back-lit displays.
• HG-101 - High Gloss Film A4. Gives documents a Gloss finish, used for reports/graphics.
• TR-101 - T-Shirt Transfer. Images can be printed onto the transfer material and then ironed onto T-shirts, Sweaters, etc..

Known Issues

Printing Gibberish When Attached to a Packard Bell PC

If the printer is attached to a Packard Bell 9000 Series PC, then go into the Control Panel and then Fonts, and look for the Font WPBOXDRAWING. If it is there, then delete it. Also check that the Canon printer is set as the default printer.

Black Page When Printing Faxes

If when you print a fax, it comes out as a solid black page, go into the printer's properties and set the printer to Mono.

Compressed first line in offline test print

When performing an offline self test, the first line is compressed. This happens when the Smoothing feature for Non-Windows applications is enabled. To stop this, disable the Smoothing function using the DOS based BJSETUP utility.

Problems with Cartridge Detection / Slow Printing With BC-02 Cartridge

When using the BC-02 cartridge, printing is very slow. Cartridge detection (or Status Self Test Page) indicates that the cartridge is either BC-05 (Color) or BC-06 (Photo). To solve this and other problems with cartridge detection,

• Power off the printer
• Hold Power for 6 Beeps
• Release Power

Will not print in color in DOS Applications

Cannot print in color even though color is selected and a BC-21e print head is installed in the printer.

When printing in color, make sure that the color cartridge (BC-21e) is installed in Holder 1, otherwise the printout will be in monochrome. Also insure that the "Print in black ink only" check box is not checked.

Power light flashes and the printer does not work

Try removing and reinstalling the cartridge.

Printer switches itself off after 1 minute

This printer has an Auto Shutoff mode, check the printer driver properties via the Control Panel under CONTROL. You can disabled it if you wish, note the printer also has an Auto Power ON mode when a print job is sent as well.

Error Codes

Power/Error State	Indicator  Color	Beeps	Cause / Error	Solution
Off	Off		No Power
On	Green		Ready
Blinks	Green		This indicates the Cartridge is not installed or not installed correctly	Reinstall the cartridge
Blinks	Orange		Unknown
On	Orange	1	Paper Pickup Error  or out of paper	Add Paper or clear paper jam and press the RESUME button
On	Orange	2	Paper Jam	Clear paper jam and press the RESUME button
Blinks	Orange	1 or 2	ROM or RAM fault	Requires service
Blinks	Orange	3	Cartridge out of position	Try reinstalling or replacing the cartridge if this fails then it requires service
Blinks	Orange	4	Carriage home position error	Requires service
Blinks	Orange	5	Waste Ink Full	Requires service
Blinks	Orange	6	Over Temperature Error	Try replacing the Cartridge if this fails then the printer requires service
Blinks	Orange	7-10	Print position or Cleaning fault	Requires service, however try removing the cartridge and make sure nothing is blocking the cartridges movement.