BJC-50 Printer

General Info:

Adapter

AD-360u

Alternative Drivers

Drivers you can use if the BJC-50 driver is not available.

• Windows : BJC-70/600/600e/800/4000
• DOS : Epson LQ-2550(LQ mode/Color)
• DOS : BJ-200/200e/200ex (BJ Mode/Black)
• DOS : BJ-5/10/10e/10ex/10sx/20 (BJ Mode/Black)
• DOS : Epson 510/850 (LQ Mode/Black)
• DOS : IBM ProPrinter X24 (BJ Mode/Black)

Battery

For Battery Pack NK-300,

• Charging
• Plug in the Adapter
• Close the printer's top lid
• The charging light should Flash or blink up to 10 hours. When fully charged, the charge light will turn off.
• A fully charge and good battery can print approx. 180 pages @ 5% coverage, but remember every print job is NOT 5%, so this value can vary greatly. Also If you leave the printer on when not printing, it will shorten the battery time.
• Discharging / Refresh
• Insure the battery pack is in the batter6; se (portable kit)
• Using a pointed object, ie a pen, press the REFRESH button (right side of battery case).
• The REFRESH light should blink up to 10 hours max.
• When the battery is discharged, the printer will start re-charging the battery.

Cartridges

• BCI-10 - Ink Tank (Black)
• BC-10 - Print Head
• BCI-11 Black - Ink Tank (Black BC-11)
• BCI-11 Color - Ink Tank (Tri Color BC-11)
• BC-11e - Print Head (Color)

Cleaning Print Head

With the printer online, hold down the RESUME button for 2 beeps.

Serial Number

Located behind battery back, remove battery

Known Issues

Will not run on battery or battery life is short after charge

Note - The printer will not print if both the Battery and the AC Adapter are plugged in at the same time. If this is not the case, then the battery may need refreshing, as follows,

• Connect the Adapter to the printer
• Close the printer cover
• Press the REFRESH button on the battery pack, the refresh light should begin flashing, it could take up to 10 hours to refresh the battery.

The battery may get a memory effect, meaning it will not charge to full capacity. This is the purpose of the REFRESH function.

The printer does not turn on

There is a power lock switch at the side of the printer beside the power connector, make sure that this is not in the lock position. Of note, if the power lock is enabled when the printer is on, you will not be able to switch the printer off.

Error Codes

Error Condition	Error LED	Power LED	Beeps	Solution
Paper Pickup	Steady	Steady	1	Add paper or restack
Paper Delivery	Steady	Steady	2	Remove any paper jammed
BJ Cartridge Not Detected	Steady	Steady	3	Re-install cartridge or replace it
Cartridge Mismatch	Steady	Steady	4	Install correct cartridge
No Battery	Steady	Steady	6	Install battery
Low Battery Warning	Steady	Steady	Long / Short	Charge battery
Manual Feed Error	Blinks	Steady	1	Check paper
Low Ink	Blinks	Steady	2	Replace cartridge
Cartridge Error	Blinks	Steady	3	Check/Reinstall cartridge, replace cartridge
Low Battery Warning	Blinks	Steady	4	Charge battery
Waste Full Warning	Blinks	Steady	5	Waste is almost full , printer needs service
Failed Battery Warning	Blinks	Steady	6	Replace battery
Service Errors	Blinks	Blinks	1-12	Requires service

If the printer does not turn on and the adapter is plugged in. There is a power lock switch at the side of the printer beside the power connector, insure this is not in the lock position. If the power lock is enabled when the printer is on, you will not be able to switch the printer off.

Waste Error Reset

1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord