BJC-600 Printer

General Info:

Alternative Drivers

Drivers you can use if the BJC-600 driver is not available.

Cartridges

Self Test

Color Pattern : With the Printer switched off, press and hold the FF button, and press the POWER button until the printer beeps. When the POWER light starts to flash, release both buttons. When the POWER light stops flashing, the printer starts to print the color pattern. To stop printing the test, press the POWER button to turn off the printer.

Font Pattern : With the printer switched off, press and hold the PRINT MODE button, and press the POWER button until the printer beeps. When the POWER light starts to flash, release both buttons. When the POWER light stops flashing, the printer starts to print the Font Pattern. To stop printing the test, press the POWER button to turn off the printer.

Nozzle Check Pattern : With the printer switched off, press and hold the ONLINE button, and press the POWER button until the printer beeps. When the POWER light starts to flash, release both buttons. When the POWER light stops flashing, the printer starts to print the Nozzle Check Pattern. To stop printing the test, press the POWER button to turn off the printer.

Serial Number

Location - Cream colored label on the back of the printer near the power cord
Prefixes - TKL...

Special Paper

 

Known Issues

Microsoft Creative Writer

In Windows 95, if you print a card to the Canon Bubble jet 600c printer from Microsoft Creative Writer for Windows 1.0 and 1.1, you may receive "out of space" error messages and may not be able to print the cards. Here is Microsoft's work around:

N.B. It might be worth trying each of the above separately, rather than all at once.

What is the efficiency rate of this printer.

Each INK cartridge contains enough ink to print about 200 pages (300,000 characters) in HQ mode, or about 400 pages (600,000 characters) in HS (high speed) mode. Printing Graphics with a 30% ink coverage (7.5% color) per page one set of ink cartridges (4 colors) will last about 135 pages.

All lights are flashing, and page 77 of manual gives error message "Waste Ink Tank Warning".

In 99% of cases, the following procedure will work:

This should totally reset the machine. If this does not work, then machine needs to be serviced.

Incorrect colors from Windows applications.

Updated driver required from Canon.

Microsoft Word and WordPerfect printing incorrectly with regard to spacing and italics.

New printer driver required.

Printer is switched off during power on sequence.

Interrupting the power on sequence can cause the printer to error. This can be caused by pressing other buttons while initialization. Switch the printer off and unplug the mains lead. Leave for several minutes and switch on.

One of the following error condition occur

The printer head is faulty, hence the errors being received.

Power and Error lights constantly lit Bk+, Plain, Envelope & Thick lights blinking. Printer will not print at all.

Although the above error light sequence is not listed in the manual, Canon state that IF the printer can be put on line and it will (attempt to) print THAT it is NOT A HARDWARE ERROR. Hardware errors, are indicated by not being able to put the printer ONLINE. The majority of problems they say will refer to the cartridge and/or the print head. In particular the separate Ink Cartridges where the 'sponge' in the cartridge must be in contact with the outlet port to allow capillary action to feed the ink from the reservoir via the sponge to the outlet port. The print head will detect if no ink is present ie: not being fed by the cartridge either because its empty or the sponge is not in contact with the cartridge outlet (cartridge defective). If the cartridges have been checked or replaced or are known to be OK (by trying them on another machine!) then it is suggested that the print head is probably faulty.

Are Print heads consumables?

NO!

 

Error Codes

Power

Beeps

Error

Online

BK

C

M

Y

Env

Thick

Error Condition

Solution

On

 

Off

On

 

 

 

 

 

 

Ready

 

On

2

On

 

 

 

 

 

 

 

Paper jam or out of paper

Add paper or remove the paper jam and press ONLINE to continue

On

2

 

 

 

 

 

 

Blink

Blink

WASTE INK warning

You can continue printing by pressing ONLINE however the printer is due for service

On

2

 

 

 

 

 

 

Blink

Blink

INK OUT - The printer is out of INK, Note any combination of BK, C, M or Y may blink

Replace or check the ink cartridges that have BLINKING lights - BK = Black, C = CYAN, M = Magenta, Y = Yellow

On

3

Blink

 

 

 

 

 

 

On

This indicates Carriage Error (Print head movement)

Requires Service

On

3

Blink

 

 

 

 

 

On

 

Home Position Error (Print head movement)

Requires Service

On

3

Blink

 

 

 

 

 

On

On

Encoder Error
(Print head movement)

Requires Service,
Though See Notes Below

On

3

Blink

 

 

 

 

On

 

 

Purge Error

Requires Service

On

3

Blink

 

 

 

 

On

 

On

Paper Feed Motor Error

Requires Service

On

3

Blink

 

 

 

 

On

On

 

Auto Sheet Feeder Home Position Error

Requires Service

On

3

Blink

 

 

 

 

On

On

On

Internal Temperature Error

Requires Service

On

3

Blink

 

 

 

On

 

 

 

WASTE INK is FULL

Requires Service

On

3

Blink

 

 

 

On

 

 

On

This indicates EEPROM Error

Requires Service

On

3

Blink

 

On

 

 

 

 

 

ROM Error

Requires Service

On

3

Blink

 

On

 

 

On

 

 

RAM Error

Requires Service

On

3

Blink

 

 

 

On

 

On

 

Gate Array Error

Requires Service

On

3

Blink

 

 

 

 

 

Blink

Blink

Print Head Error

Requires Service, Possibly remove print head and reinstall may resolve problem. Any combination of BK,C,M,Y may be blinking

Notes - Encoder Error

If you receive an encoder error, try the following,

Print mode is the button below the 4 LEDs (BkCMY)

Waste Error Reset

1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps

 

DIP Switches

The DIP Switches are located under the main cover on the left side and if viewing from the front switch 1 is on the left, OFF is nearest the front on the top of the machine.

BJ mode

Switch

Function

ON

OFF

Factory
Setting

1

Paper Width

A4

Letter

OFF

2

Text Scale

Enabled

Disabled

OFF

3

Automatic line feed

CR = CR + LF

CR = CR

OFF

4

Page Length

12" (305 mm)

11" (279mm)

OFF

5

Character Set

Set 2

Set 1

OFF

6

Auto Carriage Return

LF with CR

LF only

OFF

7

Alternate Graphics Mode

Enabled

Disabled

OFF

8

Not Used

 

 

OFF

9

Code Page

850

837

OFF

10

Not Used

 

 

OFF

11

Not Used

 

 

OFF

12

Emulation mode

Epson LQ-2550

Canon BJ

OFF

LQ mode

Switch

Function

On

Off

Factory
Setting

1

Paper Width

A4

Letter

OFF

2

Text Scale Mode

Enabled

Disabled

OFF

3

Not Used

 

 

OFF

4

Page Length

12 inches (305 mm)

11 inches (279mm)

OFF

5

Character Set

Graphics

Italics

OFF

6

International Character Set

See Table 1

OFF

7

International Character Set

See Table 1

OFF

8

International Character Set

See Table 1

OFF

9

Font

See Table 2

OFF

10

Font

See Table 2

OFF

11

Font

See Table 2

OFF

12

Emulation mode

Epson LQ-2550

Canon BJ

ON

Table 1 : International Character Set

Country

Switch 6

Switch 7

Switch 8

 

 

USA

OFF

OFF

OFF

UK

OFF

OFF

ON

Germany

OFF

ON

OFF

France

OFF

ON

ON

Denmark

ON

OFF

OFF

Sweden

ON

OFF

ON

Italy

ON

ON

OFF

Spain

ON

ON

ON

Table 2 : Font

Typeface

Switch 9

Switch 10

Switch 11

Roman

OFF

OFF

OFF

Sans Serif

OFF

OFF

ON

Draft

OFF

ON

OFF

Courier

OFF

ON

ON

Prestige

ON

OFF

OFF

Script

ON

OFF

ON

Orator

ON

ON

OFF

Orator-S

ON

ON

ON